KD Tools - Getmetools.com



    © 2011 Page updated 3/31/2011

    [SITE MAP]

    If you don't see something, just ask - we might be able to get it!

    Use Ctrl+F to find what you are looking for (Command+F for Apple users)

    KD 104 - Distributor Clamp Wrench: $20.92

    Quantity: Check out now

    • Reach around obstructions to turn the distributor lock nut with this double-ended wrench. It fits 1/2 and 9/16" lock nuts. Use an adapter to join wrenches or attach the wrench to a 3/8" ratchet or extension.

    KD 124 - Remote Control Starter Switch: $11.93

    Quantity: Check out now

    • Use to bypass the ignition switch on any engine with a solenoid starter switch. The switch lets you crank the engine while working in the engine compartment. Switch is made of heavy-duty construction and has 32"-long leads. To use, connect from the positive battery terminal to the energizing terminal of solenoid. Use the switch for generator, starter, electrical, fuel pump and compression tests and for setting ignition points and adjusting tappets. 6 and 12 Volt use only. Wire rated capacity 8 amp.

    KD 129 - Low Voltage Circuit Tester: $8.54

    Quantity: Check out now

    • Test For Voltage in 6 and 12 Volt Systems. Ground Clip and Touch Probe to Point Being Tested. Tester Bulb Will Light if Power is Present.

    KD 135 - Spark Plug Terminal Pliers: $7.26

    Quantity: Check out now

    • Safely remove spark plug cables and prevent cable damage. Pliers' handles and jaws are coated with a heavy-duy plastic for a sure grip.

    KD 145 - Hose Pinch Off Pliers: $15.28

    Quantity: Check out now

    • Pliers eliminate the need to drain cooling system when servicing. Pliers squeeze hoses shut and jaws swivel for parallel clamping. Pliers include automatic locking ratchet. Tool can be used to pinch off some emission system hoses.
    • Do not use on wire-reinforced hose

    KD 1708 - Stud Extractor: $25.78

    Quantity: Check out now

    • Tool removes 1/4" (6mm) to 3/4" (19mm) studs.
    • Cam wheel grips within 9/32" of flat surface to hold stud.
    • Drive socket will not bind.

    KD 2031 - Exhaust & Tailpipe Cutter: $33.29

    Quantity: Check out now

    • Use tool to cut pipes 3/4" to 3" (19 to 76mm) in diameter. Fifteen blades effectively cut pipe so only 1/4 turn is needed for a complete cut. Patented, serviceable tool works in hard-to-reach areas. It will not cut double-wall pipes. Keep well oiled. Not for use on stainless steel.

    KD 2038 - Window Molding Removal Tool: $9.74

    Quantity: Check out now

    • Removes window molding clips on GM, Ford and AMC vehicles. Place jaw flat against glass. Locate clips and roll them out with tip, keeping jaw flat to glass.

    KD 2078 - Universal Overhead Valve Spring Compressor: $24.28

    Quantity: Check out now

    • Remove valve springs on most cars with overhead valves without removing the cylinder head.
    • Offset jaws grip the valve spring in parallel compression.
    • Tool maintains constant length as spring is compressed.

    KD 2116 - Disc Brake Gauge: $13.74

    Quantity: Check out now

    • Gauge measures brake lining remaining on bonded pads in fractions from 1/16" to 5/8" in 1/32" graduations
    • Tool checks measurement without removing caliper

    KD 2189 - Tubing Bender: $21.50

    Quantity: Check out now

    • Bend 3/16, 1/4, 5/16 and 3/8" copper and steel tubing.
    • Tool makes tight bends without the tube collapsing.
    • Roller adapters are included for each tubing size.
    • Place tubing between the adapter and studs and squeeze the handles to bend.

    KD 2256 - Slide Hammer Puller Set: $99.43

    Quantity: Check out now

    • Slide Hammer Puller Set for outside and inside pulling of gears, bearings, pinions, grease retainers, oil seals, bearing races, and many other jobs.
    • Use as two-jaw or three-jaw puller.
    • Reversing the cone and jaws adjusts the tool for inside pulling.
    • Comes with a 2-1/2 pound hammer.
    • Slide hammer has 5/8”-18 UNF thread.

    KD 2270 - Flywheel Turner: $23.71

    Quantity: Check out now

    • Hook this tool into flywheel teeth to rotate the crankshaft.
    • Use when working on clutches, transmissions, installing rings or other jobs that require the crankshaft to be in a specific position.
    • Spring tension aids tool engagement on the flywheel.

    KD 2281 - Telescoping Magnetic Retrieving Tool: $7.74

    Quantity: Check out now

    • Tool extends from 16-3/4" to 26-3/4" to pick up hard to reach ferrous metal parts and tools.
    • It has a comfortable vinyl grip and the magnet rotates to any position.
    • Maximum lifting power is 16 ozs.
    • Magnet diameter is 1/2"

    KD 2286 - Harmonic Balancer Puller: $18.00

    Quantity: Check out now

    • Puller removes balancers, pulleys and gears with tapped holes.
    • A floating swivel prevents damage to the shaft end.
    • Four slots in the yoke allow for 2- or 3-hole applications.
    • Tool bolts to balancer with center screw on the end of the crankshaft.
    • Tighten while tapping on the screw head to remove balancer.
    • Puller includes 3/8-24 UNF, 5/16-18 UNC, 3/8-16 UNC and 10mm x 1.5 screws for most American and imported cars.

    KD 2287 - Ball Joint Separator: $16.04

    Quantity: Check out now

    • Tool Separates ball joint from steering knuckles.
    • To use, insert 15/16" opening between parts and strike with hammer.
    • Separator is forged to withstand hard usage.
    • Over all length: 12"

    KD 2288 - Tie Rod Separator: $18.04

    Quantity: Check out now

    • This powerful tool separates tie rods.
    • Insert 21/32" opening between parts and strike with hammer to separate.
    • This tool is forged to withstand hard usage.
    • Overall length: 12"

    KD 2289 - Pitman Arm Puller: $22.71

    Quantity: Check out now

    • Puller removes full-size pitman arms.
    • To use, mount jaws over pitman arm and turn center screw with wrench until tight. Strike center screw with hammer to release Pitman Arm. No Other tools are needed.
    • Puller has a drop-forged and heat-treated steel yoke
    • Screw size 5/8"-18 Thread

    KD 2321 - Oil Filter Wrench: $17.01

    Quantity: Check out now

    • Wrench features a wider band for a better grip of filters and a stronger anchor plate for removal of excessively tight filters.
    • Tool is designed for high torque requirements of truck filters.
    • Use with a 1/2" square drive tool and extension.
    • Removes Truck Filters from 4-21/32 to 5-5/32" (118 to 130mm) in Diameter.

    KD 2322 - Improved Heavy Duty Oil Filter Wrench: $17.01

    Quantity: Check out now

    • Wrench features a wider band for a better grip of filters and a stronger anchor plate for removal of excessively tight filters.
    • Tool is designed for high torque requirements of truck filters.
    • Use with a 1/2" square drive tool and extension.
    • Removes Truck Filters from 5-5/32 to 5-21/32" (130 to 143mm) in Diameter

    KD 2324 - Brake Lining Gauge: $10.94

    Quantity: Check out now

    • Gauge measures brake lining from 0 to 1/2" in 1/64" graduations.
    • Place gauge over brake shoe to take reading.

    KD 2326 - Brake Lining & Tire Tread Gauge: $9.38

    Quantity: Check out now

    • Measures the Amount of Lining Remaining On Riveted and Bonded Drum Shoes and Disc Brake Pads.
    • Measures Tire Tread Depth Up To 9/16" in Graduations of 1/64".

    KD 2389 - Engine Cylinder Ridge Reamer: $49.67

    Quantity: Check out now

    • Reamer removes ridges from top of engine cylinders with bore diameters 3 to 5" (77 to 127mm).
    • Tungsten carbide cutters and fine-thread feed-up ensure smooth cutting action.
    • Unique design lets you change from one cylinder to another without readjusting.

    KD 2391 - Flexible Retrieving Tool: $7.57

    Quantity: Check out now

    • Retrieve small objects from hard-to-reach places.
    • Push the button to open the claws and release to grab.
    • 23" Long.

    KD 2398 - Transmission Clutch Spring Compressor: $113.63

    Quantity: Check out now

    • Tool compresses automatic-transmission clutch springs on some GM, Ford, Toyota and other transmissions.
    • It permits easy removal and installation of snap rings.
    • Job can be completed without removing center shaft and clutch assembly from transmission housing.
    • To use, force legs in and catch jaws inside transmission drum groove. Loosen wing nuts and adjust pushers. Tighten screw until lock ring is free to be removed.

    KD 2414 - Steering Wheel Lock Plate Remover & Installer: $14.99

    Quantity: Check out now

    • Depresses steering wheel lock plate allowing easy removal and reassembly of snap ring.
    • A must for servicing turn signals, ignition switches, and steering locks built into the steering column.
    • Includes SAE and metric center screw adapters.
    • Set screw included to lock telescopic column in place while depressing lock plate.

    KD 2417 - Brake Bleeder Adapter: $50.74

    Quantity: Check out now

    Use adapter with 2222 or 2901 Brake Bleeder Tanks to pressurize brake systems on cars and trucks with large dual master cylinders up to 3-1/4 x 8-3/8".
    Gasket prevents leakage.
    For use on metal reservoirs only.

    Replacement Parts: • KD 2417-75: Chain $2.64

    Quantity: Check out now
    • KD 2417-76: Hook Assembly $4.67

    Quantity: Check out now

    KD 2419 - Screw Extractor Set: $8.75

    Quantity: Check out now

    • Removes screws, broken studs, set screws, pipe and alemite fillings.
    • Drill a hole in the screw and place extractor into hole. Tap lightly with hammer and turn counterclockwise with tap wrench to remove the screw. Spiral blades grip screw.

    KD 2420 - Clutch Aligning Tool Set: $20.32

    Quantity: Check out now

    • Aligns single disc clutches on American and imported cars, light trucks, and tractors.
    • Adapter fits through clutch plate and into pilot bushing or bearing.
    • Tapered cone fits into clutch hole and aligns clutch plate properly.
    • Includes shaft and eight two-stepped pilot bearing adapters for 16 sizes.
    • Plate aligning cone has 1-1/8" maximum diameter taper.

    KD 2428 - Cylinder Compression Tester: $28.47

    Quantity: Check out now

    • Checks cylinder compression from 0 to 300 psi (0-21 Kg/cm2).
    • Adapters fit 14mm and 18mm spark plug holes.
    • Special air hold valve for easy resetting of gauge.
    • 16" rubber hose.

    KD 2521 - Fuel Pump Vacuum & Pressure Tester: $16.51

    Quantity: Check out now

    • Tests for fuel line pressure and vacuum leaks.
    • Check for leaky valves, timing, fuel pump vacuum and pressure, and gas line leakage.
    • Easy-to-read gauge with 3' hose and vacuum hose adapter fitting.
    • Gauge measures vacuum from 0 to 28" Hg in 1" increments (0 to 700mm Hg in 50mm increments).
    • Measures pressure from 0 to 15 psi in 1/2 psi increments (0-1 Kg/cm2 in .1 Kg/cm2 increments).

    KD 2534 - Locking Ring Pliers: $13.21

    Quantity: Check out now

    • Remove and install snap rings without holes (E-rings) used on brakes, transmissions, pedals and clutch shafts.
    • Scored jaws hold rings securely.

    KD 2569 - Oil Pressure & Stoplight Switch Socket: $4.78

    Quantity: Check out now

    • Removes oil pressure sending unit on most engines.
    • Socket has a 1" and 1-1/16" hex opening plus recess to accommodate switch.
    • Socket also fits some brake-light switches.
    • Turn with a 15/16" wrench, or a 3/8"Square Drive Tool.
    • Length: 3".

    KD 2595 - Chain Wrench: $28.60

    Quantity: Check out now

    • To effectively apply torque, wrap tool around any shape item from 5/8 to 5" (16 to 127mm) in diameter.
    • Turn with 1/2" square drive tools. Chain length - 16 1/4".

    KD 2756 - HEI Ignition Tester: $7.74

    Quantity: Check out now

    • Accurately check for spark in ignition systems without removing spark plug from engine.
    • Testers verify that energy is sufficient for spark plug to fire.
    • Attach spark plug wire to tester end. Clamp tester to engine as ground. Crank engine and check for spark.
    • Calibrated for High-Energy Systems.

    KD 2757 - Ignition Tester Calibrated for Standard Ignitions: $6.90

    Quantity: Check out now

    • Accurately check for spark in ignition systems without removing spark plug from engine.
    • Testers verify that energy is sufficient for spark plug to fire.
    • Attach spark plug wire to tester end. Clamp tester to engine as ground. Crank engine and check for spark.
    • Calibrated for standard ignition systems.

    KD 2774 - Double-Ended Spring Tool: $6.01

    Quantity: Check out now

    • Double-ended tool removes and installs small and large car drum brake retaining springs.
    • Tool fits sizes 5/8 to 11/16" and 11/16 to 7/8" diameter.
    • Special sockets grip retaining washers.
    • Push and turn to remove or install.

    KD 2775 - Hand Bearing Packer: $20.79

    Quantity: Check out now

    • Self-contained bearing packer saves time and can be used anywhere.
    • No air line or grease gun required.
    • Packs 50 to 60 bearings without refilling.
    • Transparent, impact resistant cup allows grease level check.
    • Use on all cage-type roller and ball bearings up to 2" bore.

    KD 2790 - End Cap Oil Filter Wrench: $5.47

    Quantity: Check out now

    • Specially designed wrench removes and installs hard-to-reach 3" (76mm) oil filters with a 15-flute end.
    • It fits various flute designs found on AC/Delco, Fram, Wix, STP, NAPA, Sears, Gard, Montgomery Ward, VW, Motorcraft and other filters.
    • Use with 3/8" square drive tool or a 1" wrench.
    • Durable steel wrench is zinc plated to resist rust.
    • Be sure fluted end of filter matches wrench.

    KD 280 - Bendix Drum Brake Spring Tool: $6.64

    Quantity: Check out now

    • Tool removes and installs return spring on Bendix drum brakes.
    • To use, place socket end over spring anchor and twist to remove. Hook notched end through spring and over the post, then lift to install.

    KD 2822 - Trim Pad Removing Tool: $6.85

    Quantity: Check out now

    • Tool reaches behind trim panel on GM and other cars.
    • It grips plastic fastener and removes trim without damage.

    KD 2824 - Seal & Pilot Bearing Puller: $50.44

    Quantity: Check out now

    • Hooked end removes seals and pilot bearings without breaking.
    • Roll hook under edge of seal and hit striking block with hammer.
    • Hook can be used on slide hammer for frozen seals.
    • Puller has 1/2"-13 UNC threads.
    • Puller is not recommended for caged needle bearings. Damage to caged needle bearings may occur.

    KD 285 - Brake Shoe Retaining Spring Tool: $6.99

    Quantity: Check out now

    • Tool removes and installs retaining springs 11/16 to 7/8" in diameter.
    • Special socket grips retaining washer.
    • Push and turn to remove or install.

    KD 287 - Drum Brake Adjusting Tool: $3.71

    Quantity: Check out now

    • Tool adjusts clearance between drum brake and brake shoe.
    • It fits through a slot in the backing plate and turns the star wheel in many drum brakes.

    KD 2897 - Pulley Remover & Installer: $50.03

    Quantity: Check out now

    • Remove pressed-on alternator and power steering pulleys on late-model GM, Ford, Chrysler engines.
    • The threaded end installs late-model GM alternator and power steering pulleys, including Quad 4.
    • Reverse the jaws to pull the alternator internal bearing.
    • The puller fits some AMCs.
    • Will not work on 3.3L and 3.5L Chrysler engines.

    KD 2901 - Brake Bleeder Tank: $138.44

    Quantity: Check out now

    • Safe, portable tank fills and pressurizes standard and power brake systems.
    • It operates from hand pump pressure, eliminating the need for an air compressor.
    • Only a few pumps are needed to build pressure to 10 to 15 PSI - excessive pressure cannot build up.
    • Tank is serviceable and features quick disconnect coupler and shut-off valve that is used as a source for brake fluid when topping off master cylinders with brake bleeder adapter attached.
    • It has a 4-qt. capacity and a 10-1/2' hose.
    • Adapters are available for many cars.

    KD 295 - Brake Adjusting Tool: $6.25

    Quantity: Check out now

    • Tool adjusts clearance between drum brake and brake shoe.
    • It fits through a slot in the backing plate and turns the star wheel.
    • Ends of tool are offset for hard-to-reach areas on small cars.

    KD 2951 - 3/8" Drive Micrometer Style Torque Wrench: $145.67

    Quantity: Check out now

    • Adjustable 3/8" Drive Ratchet Head Torque Wrench,
    • 10-100 ft.lb. (16.9-138.9 Nm) Adjustable in .5 ft./lbs. steps

    KD 2952 - 1/2" Drive Micrometer Style Torque Wrench: $138.69

    Quantity: Check out now

    • Adjustable 3/8" Drive Ratchet Head Torque Wrench,
    30 to 250 ft-lb (47.45 to 345.68 Nm) Adjustable in 1 ft./lb. steps

    KD 2953 - 3/4" Drive Micrometer Style Torque Wrench: $465.69

    Quantity: Check out now

    • Torque range: 100 to 600 ft.-lbs in 2.5lb increments; (153 to 830 Nm in 3.4 Nm increments)
    • Reversible for torquing left or right threaded fasteners
    • Accurate in clockwise direction to +/- 4% in upper 80% of range
    • Micrometer lock-ring maintains setting during operation
    • Rubber dust seal keeps dirt out of inner mechanism
    • 45 tooth ratchet design yeilds 8 degree arc for work in tight spaces
    • Chrome finish for long lasting corrosion resistance
    • Length: 41.25"
    • Includes storage box

    KD 2967 - Hand Held Tachometer: $103.85

    Quantity: Check out now

    • Tachometer checks diesels, pumps, compressors, power take-offs andfarm and construction equipment revolution speed.
    • Tool is ideal where an electric tachometer cannot be used.
    • To use, hold rubber tip against end of rotating shaft and read revolutions per minute directly from dial.
    • Range is 100 to 4000 rpm (clockwise or counterclockwise).
    • Length: 4-1/4". Diameter: 2-3/4".

    KD 2968 - Angle Finder: $33.78

    Quantity: Check out now

    • Use finder to measure angles of most parts such as frame angle (pitch forward or backward) for setting truck front ends.
    • A magnet in the base holds tool in place.
    • It is graduated in 1/2" increments.

    KD 298 - Brake Spring Pliers: $15.69

    Quantity: Check out now

    • Tool easily removes and installs shoe return springs on most drum brakes.
    • Socket end removes spring from anchor stud and notched end installs spring on anchor.
    • Tool is chrome plated to resist rust and provides easy cleanup.

    KD 3136 - Ford Fan Clutch Wrench Set: $41.17

    Quantity: Check out now

    • Set is used to remove and replace the thermostatic fan assembly on Ford 4.9-L E and F series truck engines 1984 through 1993, Ford 4.6-L modular engines, 2.8-L engines 1984 through 1987, 2.9 to 3.0-L Engines, 1988 to current,and 4.0-L engines 1990 to current.
    • Use with 1/2" square drive tools and torque wrench.
    • Refer to Ford factory service manual for torque specifications and thread direction.
    • Wrench Openings - Long: 36mm (1.417"), Short: 58mm (2.283").
    • 3136-76 Long Wrench 36mm 3136-77 Short Wrench 58mm.

    KD 3150 - Small Convertible Internal/External Snap Ring Pliers: $22.97

    Quantity: Check out now

    • Easily convert for either external or internal use on snap rings.
    • Unique push-button feature allows for effortless change.
    • Tool comes with heavy-duty cushion-grip handles to provide comfort and broached jaws for tip control and stability.
    • Use pliers on small internal or external snap rings where space is limited.
    • Pliers fit internal ring sizes 1/4 through 1" (6.4 through 25.4mm) and external ring sizes 1/8 through 1" (3.2 through 25.4mm).
    • Pliers include 5 pairs of color-coded tips in sizes 0.023 straight, 0.036 and 0.047 straight and 90บ. Hex stock size of tips .092".

    KD 3151 - Large Convertible Internal/External Snap Ring Pliers: $23.68

    Quantity: Check out now

    • Easily convert for either external or internal use on snap rings.
    • Unique push-button feature allows for effortless change.
    • Tool comes with heavy-duty cushion-grip handles to provide comfort and broached jaws for tip control and stability.
    • Use pliers on most internal snap-rings 3/8 through 2" (9.5 through 50.8mm) and external snap rings 1/4 through 2" (6.4 through 50.8mm).
    • Pliers include 5 pairs of color-coded tips in sizes 0.036, 0.047 straight and 90บ and 0.070 straight.
    • Hex stock size of tips .092".

    KD 3152 - Extra Large Convertible Internal/External Snap Ring Pliers: $52.53

    Quantity: Check out now

    • Easily convert for either external or internal use on snap rings.
    • Unique push-button feature allows for effortless change.
    • Tool comes with heavy-duty cushion-grip handles to provide comfort and broached jaws for tip control and stability.
    • Use on large internal and external snap rings including automatic transmissions.
    • Pliers fit internal rings 1-13/16 through 4" (46 through 101.6mm) and external rings 1-1/2 through 4" (38.1 through 101.6mm).
    • Pliers feature ratchet lock to hold the snap ring in desired position and includes 6 pairs of color-coded alloy steel tips in sizes 0.090, 0.108 and 0.120 bent to 15บ and 90บ.
    • Hex stock size of tips .156".

    KD 3163 - Disc Brake Piston Tool: $7.06

    Quantity: Check out now

    • Designed to rotate the parking-brake-activated piston back into the caliper cylinder when replacing worn pads on vehicles equipped with 4-wheel disc brakes.
    • Tool will function on most domestic and import vehicles.

    KD 3164 - Inner CV Joint Puller Adapter: $31.18

    Quantity: Check out now

    • Used with 2-1/2-lb slide hammer (2290), this tool will pull most CV joints that use a hidden snap ring to hold them in the transaxle.
    • Inner CV Joint Puller fits slide hammer with 1/2"-13 UNC threads.
    • Works on GM and some Ford vehicles.

    KD 3191 - CV Joint Boot Clamp Tightening Wrench: $16.14

    Quantity: Check out now

    • Use wrench to securely fasten Band-itฎ style free end clamps, roll band and clips or Band-it Jr.ฎ style pre-formed CV Boot Clamps.
    • The tool is used by turning the winding mandrel with a 1/2" socket or wrench.
    • The mandrel tightens the clamp, holding it in place until the ears of the clamp are folded down.

    KD 3246 - 4-Wheel-Drive Spindle Nut Wrench: $32.28

    Quantity: Check out now

    • Four-lug wrench removes spindle nuts on 4-wheel drive vehicles.
    • It features uniquely designed lugs for maximum strength.
    • Use with 1/2" square drive tool.
    • Will work on Ford vehicles with ratcheting type lock nuts on front axle.
    Application:
    • 1981-1997 Ford F250-350, Bronco with Dana Axle, or Dana 50IFS or model 60 monobeam axle outer adjusting nut.
    • 1982-1990 GM Heavy Duty 3/4 and 1 ton trucks
    Dimensions:
    • OD: 2.63
    • ID: 2.27
    • Length: 3.24
    • Inside Depth: 3.0

    KD 3253 - 65mm End Cap Filter Wrench: $5.69

    Quantity: Check out now

    • Wrench removes and installs 14-flute, 65mm factory oil filters on late-model Toyota Tercel, MR2, Celica and 1988 Camry.
    • Use with a 3/8" drive tool or a 1" wrench.

    KD 3255 - Crankshaft Hub Bolt Wrench: $24.09

    Quantity: Check out now

    • This 19mm wrench easily removes and installs all types of crankshaft pulleys used on Ford Escort/Lynx 1.6- and 1.9-L engines and allows for in-vehicle replacement of timing belts.
    • Use wrench with a 1/2" square drive tool.
    • Refer to Ford factory service manual for proper procedure and torque specifications.

    KD 3259 - Universal Vacuum PVS, TVS Valve and Oxygen Sensor Socket: $15.85

    Quantity: Check out now

    • Specially designed socket is for removal and replacement of vacuum switches with a 7/8" hex currently found on Ford, GM, Chrysler and some import vehicles.
    • Also used to remove and replace some oxygen sensors.
    • Use with a 1/2" square drive tool or 7/8" wrench. Socket depth: 3-1/8".

    KD 3288 - Universal 3 Jaw Oil Filter Wrench: $10.81

    Quantity: Check out now

    • Remove all passenger car and light-duty truck spin-on type filters with this wrench. Sizes range from 2-1/2 to 3-3/4".
    • Use with 3/8" square drive tool.

    KD 3290 - Ford A/C and Fuel Line Spring Lock Coupling Tool: $11.90

    Quantity: Check out now

    • Most Ford vehicles are equipped with spring lock couplings on fuel and air conditioning lines.
    • Necessary tool releases locking mechanism on all 4 sizes: A (3/4"), B (5/8"), C (1/2") and D (3/8").

    KD 3296 - Ford Fan Clutch Wrench Set, 6.9 and 7.3L: $63.42

    Quantity: Check out now

    • Use set to remove and replace the thermostatic fan assembly on Ford 6.9- and 7.3-L engines.
    • Use with 1/2" drive tools and a torque wrench.
    • Refer to Ford factory service manual for torque specifications and thread direction.
    • Wrench openings - Long: 48mm (1.889"), Short: 83mm (3.250").
    • See KD 3472 and 3473 for expanded coverage.

    KD 3312 - Deluxe Inner Tie Rod Tool: $41.75

    Quantity: Check out now

    • Remove and install inner tie rods on many GM and some Chrysler products that have a complete hex with a ball socket or just 2 flats on the inner end that measure 1-7/16" across.
    • Tool can also be used on all inner tie rods with 1-3/16" and 1-5/16" hex sizes.

    KD 3321 - Fuel Line Quick Disconnect Tool: $12.78

    Quantity: Check out now

    • Tool releases the fuel line locking mechanism on 1989 and newer GM, 1990 and newer Ford and some 1990 and newer Mazda vehicles.
    • Fits 5/16" and 3/8" fuel lines.

    KD 3340 - GM Clutch Plate Remover & Installer: $36.65

    Quantity: Check out now

    • Remove and install clutches on GM air conditioning DA6 and V5 compressor clutches without removing retaining ring.
    • Install clutch plate with compressor on car.
    • Metric threads.

    KD 3358 - Wheel Weight Tool: $26.58

    Quantity: Check out now

    • Tool installs, removes, trims and tightens all types of clip-on wheel weights.
    • It features a special plastic-type material on the hammer head for safe, mar-free installation of specially coated wheel weights used on alloy wheels.
    • Tool has a plastisol-dipped handle for comfort.

    KD 3367 - Side Terminal Battery Wrench: $8.92

    Quantity: Check out now

    • Use wrench for most GM side terminal batteries or any 5/16" battery terminal bolts.
    • It has an insulated handle to reduce risk of electrical shock and reversible 5/16" ratcheting box wrench.
    • Tool is nickel plated for durability and corrosion resistance.

    KD 3376 - Disc Brake Pad Spreader: $7.07

    Quantity: Check out now

    • Pushes the caliper piston back on disc brakes that do not have the parking brake mechanism as part of the disc brake caliper.

    KD 3410 - Ford Module Wrench: $12.26

    Quantity: Check out now

    • Use wrench to remove and install Ford ignition modules without removing or moving distributor.
    • Dual-ended ratchet wrench features both 7/32" (5.5mm) and T-20 Torxฎ for most Ford applications.
    • Wrench is designed with 25บ offset to fit in confined areas.

    KD 3414 - Serpentine Belt Tool: $35.14

    Quantity: Check out now

    Item No.DescriptionFits
    3414-80Long Handle WrenchFord 1.9 and 2.3 L, GM 3.1 L
    3414-81Short BarChrysler 2.5 and 3.0 L, Ford 4.6 L
    3414-823/8" Dr. 12 Pt. 15mm SocketFord 3.0 and 3.8 L, Chrysler 3.0, 3.3 and 3.8 L, GM 2.2, 2.8, 3.8 and 5.7 L
    3414-833/8" Dr. 12 Pt. 16mm SocketFord 3.8 and 4.0 L
    3414-843/8" Dr. 12 Pt. 18mm SocketGM3800
    3414-853/8" Dr. 13mm Crowfoot WrenchGM Quad Four Engine
    3414-863/8" Dr. 14mm Crowfoot WrenchSaturn Engine
    3414-873/8" Dr. 15mm Crowfoot WrenchFord Windstar with 3.8 L Engine

    KD 3422 - Ford 4.9L Fan Clutch Wrench: $14.90

    Quantity: Check out now

    • Wrench removes thermostatic fan assembly on 1993 to current 4.9-L Ford Engines.
    • Use in conjunction with 3136-77 58mm Short Wrench or New Universal Pulley Holder 3471.
    • Both hold pulley while turning square shaft on fan clutch.
    • Wrench opening is 40mm (1.575").

    KD 3472 - Pulley Holder / Fan Clutch Tool Kit: $51.26

    Quantity: Check out now

    • Includes the Universal Pulley Holder part # 3471 plus fan clutch wrenches # 3422 and 3136-76.
    • Used to remove and replace thermostatic fan assemblies while eliminating the need for various size holding wrenches.
    • Applications include: Ford trucks w/2.8L, 2.9L, 3.0L, 4.0L, 4.9L, and 5.0L engines. Dodge trucks w/3.9L, 5.2L, 5.9L, 8.0L V10 engines. GM trucks w/4.3L, 5.0L and 5.7L engines. Jeeps w/5.2L engines.

    KD 3473 - Ford Diesel Fan Clutch Wrench: $19.75

    Quantity: Check out now

    • Use in conjunction with the Universal Pulley Holder (3471) to remove and replace the thermostatic fan assembly on Ford 6.9L, 7.3L, and 7.3L DIT diesel engines.
    • Use with 1/2" drive tools and a torque wrench.
    • Refer to Ford factory service manual for torque specifications and thread direction.
    • Wrench opening is 48mm (1.889").

    KD 3481 - 12 Piece Rethreading Kit For Axle Spindles: $61.54

    Quantity: Check out now

    • 12-piece thread restoring die set for proper repair or renewal of damaged threads in stub axles/spindles on most vehicles (refer to automotive manuals for correct size for applications).
    • Dies will remove nicks and burrs in existing threads and are intended for “chasing” - not cutting new threads.
    • Dies are packaged in a plastic case and include the following 12 most popular sizes:
    * 3/4"-16, 3/4" -20, 13/16"-20, 27/32"-20
    * M16 x 1, M16 x 1.5, M20 x 1, M20 x 1.5, M22 x 1.5, M24 x 1.5, M24 x 2, M27 x 2.
    • Rethreading dies are made from high tempered steel for strength and durability and are hex shaped for use with a socket or wrench (not for use with impact gun).

    KD 3482 - ISO / Bubble Type Tube Flaring Kit: $63.13

    Quantity: Check out now

    • Forms International Standard bubble flare in one fast operation. For 4.75 (3/16"), 6, 8 and 10mm tubing.
    • Flares soft double wall steel tubing with a wall thickness to .028".
    • Flares metric hydraulic brake lines used on European, Japanese and domestic automobiles and light trucks.
    • Can also be used on industrial applications where vibration is a problem.

    KD 3508 - Ratcheting Oil Filter Pliers: $28.22

    Quantity: Check out now

    • Pliers cover a complete range of filter removal from 2" to 5" (50mm to 125mm) in diameter.
    • Ratchet and lock mechanism allow for multiple settings for sure fit, eliminating slippage.
    • Jaws are grooved for better holding of the filter.
    • Forged for superior strength.
    • Plastisol coated handles provide a firm grip.

    KD 3509 - Steering Wheel Lock Plate Remover: $22.61

    Quantity: Check out now

    • Features a redesigned puller yoke to fit late model GM cars with (S.I.R.) air bags. (1992 to Present).
    • Works on older GM, Chrysler and AMC vehicles previously serviced by the 2414.
    • Narrower yoke prevents damage to the lock plate.
    • Separate SAE (black) and Metric (zinc) threaded collars screw to the center steering column.
    • Center screw uses a 3/8" wrench flats to turn collars onto center column.
    • Hex screw supplied will lock down telescoping steering columns while removing lock plate.
    • Hex screw can be stored on side of puller yoke.
    • Zinc and black oxide for corrosion resistance.

    KD 3511 - Steering Wheel Puller Kit: $66.47

    Quantity: Check out now

    Kit includes:
    • 2291: Steering Wheel Puller pulls steering wheels on most US and impost cars.
    Includes special (5/16" -UNC) bolts for use on GM vehicles with S.I.R. units to avoid damaging electrical components.
    Floating swivel on center screw to prevent damage to steering column.
    Five sets of side bolts includes: 3/8-16, 5/16-18, 5/16-24, 1/4-28 and 8mm.
    Can be used to remove crankshaft pulleys on Chrysler 2.2 and 2.5L engines.
    • 3509: Steering Wheel Lock Plate Tool.
    • 3510: GM Steering Wheel Puller Legs

    KD 3526 - Ford 7.3L Fuel Filter Tool: $15.85

    Quantity: Check out now

    • Design allows for easy removal and installation of Ford 7.3L Diesel fuel caps and other diesel filter systems using the same configuration.
    • Works with fuel caps from 1995 to present.
    • Improves ability to remove and install caps where access is a problem.
    • Patented.

    KD 3529 - Heavy Duty Oil Filter Strap Wrench: $24.92

    Quantity: Check out now

    • Strap is made of high strength oil resistant nylon and handle is made of forged steel.
    • Chrome plated 3/8 and 1/2" drive engagement.
    • Handles filters with diameters up to 9" (229mm) especially high torque requirements on truck and tractors.

    KD 3530 - Low Profile Fuel Line Disconnect Set: $6.94

    Quantity: Check out now

    • Contains five popular size Air Conditioning and Fuel Line quick disconnect tools for hard to reach areas.
    • Flexible plastic design allows for easy application over tubing to access disconnects.
    • Sizes include: 7/8" (22mm), 3/4" (19mm), 5/8" (16mm) 3/8" (9mm) and 7/16" (8mm).

    KD 3533 - Outer Tie Rod Remover: $81.86

    Quantity: Check out now

    • Works on FWD and RWD import and domestic vehicles with cast or stamped steel steering knuckles.
    • Jaws apply to 5 tons of force; special design prevents jaws from slipping.

    KD 3571 - 5-20 Ton Locking Puller Assortment: $593.65

    Quantity: Check out now

    • The 3571 versatile puller set is just what you need for removing tough press fit parts quickly and easily.
    • Tool Board Size: 16" x 26" (406mm x 660mm) Weight: 42 lbs. (19.1 kg)

    3571 set includes all items listed below:
    3613 - 5 Ton 3 Jaw 4"
    3614 - 10 Ton 3 Jaw 6"
    3604 - 6 Ton 2 Jaw 6"
    3616 - 20 Ton 3 Jaw 10"
    3613-72 - Tip Protector
    3614-72 - Tip Protector
    3615-72 - Tip Protector

    KD 3588 - 3 Piece Line Clamp Set: $19.42

    Quantity: Check out now

    • 3 Piece Set

    KD 3680 - Serpentine Belt Tool: $63.92

    Quantity: Check out now

    • Same extensive coverage as the KD 3414, but with the convenience of “GearWrench” Technology.
    • 100% coverage of all vehicles including the 3/4 Volvo.
    • Easy access with both crows foot and socket sizes.
    • GearWrench provides exceptional access and ease of use.
    • Stores in Blow Molded case.
    • Tool can only be used with KDT special slim line sockets, included.

    KD 3702 - Hog Ring Plier Set: $33.10

    Quantity: Check out now

    • Specially designed for installation of Hog Ring fasterners.
    • Grips and holds hog ring during closure.
    • Spring loaded to hold ring in jaws during use.
    • Cushioned grip handle.
    • Includes both 45 and Straight hog ring pliers.

    KD 3840 - Cam Clamp – Universal Timing Gear Locking Tool: $36.83

    Quantity: Check out now

    • The KD 3840 CamClamp – Universal Timing Gear Tool is specifically designed to retain sprocket wheels to maintain proper timing during Timing belt service. This is critical, since the timing of Dual Overhead Systems is time consuming and expensive if the cams get out of position during belt service. Works on both Dual and Quad systems. What makes the KD version the better value is that it is the Patented Uni-Tooth design works on both USA and Imports by gripping the geared side of the Cam Sprocket. Competitive designs grip the inside walls, do not have a positive grip, and are prone to slippage particularly above spacing of 1”. Plus the KD version is priced more than 50% less than many competitve models. A major plus for Quad applications requiring 2 tools.
    • Fits Gears with diameters from 4 to 6” and spacing up to 3”.

    KD 3870 - 7 Piece Magnetic Oil Drail Plug Socket Set: $52.67

    Quantity: Check out now

    • Magnetic Socket Core Holds Drain Plug During Use - This Keeps Hands and Drain Plug out of Hot Oil and allows for easier one handed plug removal and installation.
    • Contains the most popular metric sizes (13mm - 19mm) for oil drain applications.
    • Sockets are color coded for easy identification.
    • Quick change design with included GearRatchet handle or use with any 3/8” drive ratchet.
    • GearRatchet handle only requires 5ฐ swing arc.
    • Set can also be used for a number of special access situations where this tools low profile design and magnetic core are an advantage.
    • Set comes complete in a blow molded case.
    • Kit includes: 13mm Plug Socket - Red, 14mm Plug Socket - Green, 15mm Plug Socket - Purple, 16mm Plug Socket - Gold, 17mm Plug Socket - Black, 19mm Plug Socket - Blue and 3/8" (20mm) Drive GearRatchet™ Handle.

    KD 3888 - 80 Degree Push Pin Pliers: $20.01

    Quantity: Check out now

    • Specially designed for removal of push pins with center locking pin.
    • Quickly removes plastic anchors that have center pins without damage to pins or anchor.
    • Tool lifts the center pin and pulls anchor in one simple step.
    • Anchors common on Honda, Toyota, GM, Ford, Chrysler and many other late model vehicles.
    • New Push Pin Plier fits into pin slots and under the center pin.
    • Double cushion grip handle.
    • Tapered end for easy access and 80ฐ offset.
    • Patent Pending.

    KD 3931 - 9/16" Ford Triton Magnetic Spark Plug Socket: $7.63

    Quantity: Check out now

    • For removal and installation of 2004 and newer F-150 pickups and other vehicles with the 5.4L 3 valve Triton engines.

    KD 3950 - 2 Piece 6.0L Powerstroke Fan Clutch Kit: $40.43

    Quantity: Check out now

    • New holder tool for removal and installation of Ford 6.0L PowerStroke Diesel engines from 2003 to present.
    • Designed for Fan Clutch removal on 2003 and above Ford 6.0L Powerstroke engines.
    • Unique fan clutch wrench grips and securely holds the pulley housing.
    • Fan clutch holding tool loosens and removes oval or round hole clutch nut.

    KD 41520 - 15 Piece Brake Service Kit: $71.74

    Quantity: Check out now

    • Kit works on both disc and drum brake systems
    • Use to adjust clearance between drum brakes and shoe, remove and install shoe return springs and brake pads
    • Includes Drum Brake Adjusting Tool which adjusts clearance between drum brake and brake shoe by fitting through backing plate slot and turning the star wheel
    • Includes Brake Spring Pliers - Hook end removes and installs shoe return spring on most drum brakes. Socket end removes spring from anchor stud and notched end installs spring on anchor
    • Includes Universal Brake Shoe Retaining Spring Tool - Removes and installs small and large car drum brake retaining springs sizes 5/8 in. -11/16 in. and 11/16 in. -7/8 in. diameter

    Other tools included are:
    • Disc Brake Piston Tool - Use on most domestic and import vehicles to rotate the parking brake activated piston back into the caliper cylinder.
    • GM-Ford Disc Brake Piston Tool - Rotates the piston back on GM and Ford vehicles with rear wheel disc brakes. Fits GM vehicles with 2-1/8 in. and 1-7/8 in. pistons and Ford vehicles 1987 to current with rear disc brakes. Ford Applications: 1987- current T-Bird, 1988-current Continental, Mark VII, 1990-current Probe, Taurus/Sable, 1991-current Town Car, 1992-current Crown Victoria, Cougar, Grand Marquis
    • Disc Brake Pad Spreader - Pushes the caliper piston back on disc brakes that do not have the parking brake mechanism as part of the disc brake caliper
    • Heavy Duty Truck Brake Spring Tool - Provides access around emergency brake lever without removal to remove and install brake retaining spring on medium duty trucks. 1988-97 Ford 450, 1967-97 Ford F250, F350, E200, E250 & E350, 1981-93 Dodge D300 & D350, 1975-93 Dodge W300 and W350, 1970-93 Dodge B300 and B350, 1974-84 Dodge 400 and 500 Series.
    • 7mm, 8mm, 10mm, 1/4 in. and 3/8 in. hex sockets
    • T40, T45 and T50 Torxฎ Sockets
    • Packaged in a blow molded case with laminated instruction cards or sticker integrated into case design for handy reference of application information; individual part numbers molded into case for easy reference and removable hinge style lid allows for convenient storage in tool box drawers

    KD 41580 - Fan Clutch Service Kit: $83.42

    Quantity: Check out now

    • This versatile kit covers most vehicles with bolt or pulleys and also newer Chrysler engines with press on pulleys requiring special pins to hold housing.
    • Features the patented 35W universal pulley holder.
    • Kit includes: Universal Pulley Holder, Pin Set Small (5 x 8mm), Pin Set Large (Cam Pins, 6 x 10mm, 7.5 x 18mm), 22mm Fan Nut Wrench, 36mm Fan Nut Wrench, 40mm Fan Nut Wrench, 47mm Fan Nut Wrench and a 50mm Fan Nut Wrench.

    KD 41600 - Master Bolt Grip Kit - Multi-Use Puller Kit: $45.96

    Quantity: Check out now

    • Master Bolt Grip Kit works on harmonic balancers, steering wheels, crankshaft pulleys, and gears.
    • Capable of handling almost every two or three-way bolt pull possible on most cars, pickups, SUVs, and small engines.

    Kit Contents:
    Two or three way yoke
    4 pc. tip set
    Metric bolt set
    SAE bolt set
    Center screw for puller (2)

    KD 41630 - Bearing Race & Seal Driver Kit: $47.72

    Quantity: Check out now

    • Allows you to install tapered bearing races and seals without damage to the component or housing
    • Includes a driver handle plus 9 popular bearing and seal drivers ranging from 1.565” to 3.180”

    KD 41690 - Front End Service Kit: $98.17

    Quantity: Check out now

    • This versatile set allows for easy removal of the most popular types of Pitman arms, tie rods, and ball joints
    • Kit Contents: 2289 Pitman Arm Puller 22 x 140mm, 3533 Tie Rod Puller, 3916 Universal Ball Joint Separator, 3917 Tie Rod End Puller and Pitman Arm Puller, and 3918 Universal Tie Rod End Remover

    KD 41710 - Rear Axle Bearing Puller Kit: $32.32

    Quantity: Check out now

    • Three pullers designed to make the removal of semi-floating rear axle bearings easier on most domestic cars.
    • Includes: 1 in. x 1-7/8 in. Puller, 1-5/16 in. x 2-2/8 in. Puller, 1-3/8 in. x 2-7/8 in. Puller.
    • Packaged in a blow molded case with laminated instruction cards or stickers integrated into case design for handy reference of application information.
    • Removable hinged style lid allows for convenient storage in tool box drawers.
    • Individual part numbers molded into case for easy reference.
    • Applications: 1 in. x 1-7/8 in. Puller - fits minimum bearing tube I.D. of 1 in. and maximum axle tube I.D. of 1-7/8 in. 1-5/16 in. x 2-3/8 in. Puller - fits minimum bearing tube I.D. of 1-5/16 in. and maximum axle tube I.D. of 2-3/8 in. 1-3/8 in. x 2-7/8 in. Puller - fits minimum bearing tube I.D. of 1-3/8 in. and maximum axle tube I.D. of 2-7/8 in.

    KD 41740 - 3 Piece 5/8" Magnetic Universal Spark Plug Service Kit: $40.90

    Quantity: Check out now

    • Long reach magnetic swivel spark plug set in 4", 6", and 11" lengths.
    • Features magnetic core on each size.
    • Lifetime warranty.

    KD 41770 - 3 Piece Oil Pump Primer Kit: $35.71

    Quantity: Check out now

    • Oil Pump Primers protect freshly rebuilt or modified engines from premature wear caused by a dry start.
    • Kit contents: GM Oil Pump Primer, Ford Oil Pump Primer 5/16” Hex Drive and Ford Oil Pump Primer 1/4” Hex Drive

    KD 41780 - General Purpose Bushing Driver Kit: $35.71

    Quantity: Check out now

    • Perfect for removing and inserting bushings in cars, trucks buses, tractors, construction and off-road equipment. This set includes small, medium, and large drivers and bushing adapters from 3/8” to 1-3/8”

    KD 41830 - 3 Piece Oil Canister Socket Set: $29.92

    Quantity: Check out now

    • Kit includes: 32mm Oil Filter Cap Wrench, 27mm Oil Filter Cap Wrench and 36mm Oil Filter Cap Wrench.
    • Comes complete in blow molded case.
    • Low profile.
    • Black oxide finish, laser marked.
    • 27mm used on VW.
    • 32mm used on GM and Saturn.
    • 36mm used on Volvo, VW, and Ford trucks.

    KD 41840 - 2 Piece Push Pin Plier Set: $31.40

    Quantity: Check out now

    • Kit includes: New 80ฐ Push Pin Plier and an original Straight Tip Push Pin Plier

    KD 61059 - 2 Piece Fuel Line Disconnect Kit: $18.04

    Quantity: Check out now

    • Set includes disconnect tools for use on many Ford, GM and Mazda vehicles.
    • Also used on Chrysler and Ford A/C Line Adapters.

    KD 61079 - Wire Strippers: $8.99

    Quantity: Check out now

    • Easy adjustable wire stripper, strips both solid and stranded wire.
    • Strips from 10 to 22 gauge wire.
    • Cushion Grip Handle.
    • Spring Loaded.
    • Adjustment knob for presets.

    KD 61094 - Tote & Promote Assortment: $217.55

    Quantity: Check out now

    • 8 of the newest and/or best selling items by KD Tools
    • Free KD Tools canvas tool tote bag ($31.75 retail value.)
    • Includes 1 each:
    KD3714 - 11 piece quick change punch and chisel set
    KD3729 - push pin plier - spring loaded
    KD3708 - 7 piece hook and pick set
    KD3792 - 1-1/4 in. hose pinch off pliers
    KD3859 - 6 piece cam-lock snap ring plier set
    KD3865 - 5 piece oil filter and wrench set
    KD3840 - cam clamp
    KD3841 - brake spring clamp

    KD 715 - Universal Nut Cracker: $31.74

    Quantity: Check out now

    • Splits most stubborn nuts 7/16" (11mm) through 3/4" (19mm) across the flats.
    • Works in channels not accessible to other tools.
    • Parallel action of pusher cracks nuts without damaging bolt threads.
    • Chisel rotates 360บ to line up parallel to bolt.
    • Simply tighten the screw until the nut splits.
    • Has rugged drop-forged frame.
    • Do not use on heat-treated nuts.
    • Length: 6-3/4".

    KD 730 - 14 & 18 MM Spark Plug Open Thread Chaser: $4.44

    Quantity: Check out now

    • Clean and restore spark plug threads with a 13/16" socket.
    • Rubber ring eliminates slipping.
    • Tool services most cars.

    KD 835 - Mechanics Stethoscope: $14.11

    Quantity: Check out now

    • Stethoscope locates the source of engine noise quickly.
    • Listen for trouble by tracing the sound of flowing water, oil, gas or steam.
    • Identify piston slap, worn gears, faulty valves, water pump failure, damaged gaskets and defective bearings.
    • Stethoscope has a shock-resistant handle and disassembles for storage.

    KD 850 - Piston Ring Compressor Set: $63.14

    Quantity: Check out now

    • Install pistons from 2-7/8 to 4-3/8" (73 to 111mm).
    • Pliers can be used parallel or perpendicular to the cylinder block.
    • Fine-tooth ratcheting lock allows you to compress bands in small increments.
    • Set works by placing a band around the piston, covering the rings and hooking pliers into the band and squeezing. With the band tightly around the piston, insert piston into cylinder and tap lightly with hammer handle to install.
    • Set includes pliers and 6 bands, 1119 through 1124.

    KD 890040 - 39 Piece GearWrenchฎ Hex/TORXฎ/Phillips/ Slotted Vortex™ Bit Socket Set: $51.94

    Quantity: Check out now

    Includes: • #1, #2, #3 Phillips Bits
    • 1/8, 3/16, 1/4 Slotted
    • T8, T10, T15, T20, T25, T27, T30, T40, T45, T47, T50, T55 Torx
    • 1/16 through 3/8 SAE Hex
    • 2mm, 2.5mm, 3mm through 8mm, and 10mm Metric Bits
    • Vortex Bit Sockets - Use with GearRatchet or use with 1/4" and 3/8 conventional square drive ratchet

    KD 8916 - 16 Piece GearDriver Combination Nut Driver Set: $61.17

    Quantity: Check out now

    Latest innovation utilizing GearForce Technology brings a new standard in ratcheting drive tools. Fine tooth ratcheting mechanism for proven strength and fine ratcheting arc. Interchangeable Nut Driver Shafts covering a variety of SAE and Metric applications. Contoured handle features a dual durometer grip for exceptional comfort and high torque. Packaged in a case. Includes: 1 - Stubby GearDriver Handle. 7 - Interchangeable Fractional Nut Driver Shafts: 3/16", 1/4", 5/16", 11/32", 3/8", 7/16", and 1/2". 8 - Interchangeable Metric Nut Driver Shafts: 5, 6, 7, 8, 9, 10, 11, and 12mm.


    © 2011 Page updated 3/31/2011

    [SITE MAP]